65 bombas de alimentação do filtro prensa zjw
Bombas de lama centrífugas horizontais em cantilever / bombas de lama revestidas de borracha / bombas de lama R55 / bombas de lama de vedação / bombas de lama de vedação centrífuga / bombas de lama de borracha resistentes ao desgaste / bombas de lama intercambiáveis / Bombas de lama para lavagem de carvão / Bombas de lama de manuseio de areia e cascalho / Manuseio de efluente bombas / bombas de processamento de flotação de minerais / bombas de lavagem de carvão / bombas de alimentação
A bomba de alimentação da prensa de filtro da série Naipu® NP-ZJW aceita desin hidráulico exclusivo e modo de instalação do
impulsor, certifique-se de que a curva de desempenho da bomba seja mais íngreme do que as bombas normais, é mais adequado para uso no
A alimentação da prensa do filtro varia de acordo com as mudanças da resistência, a fim de realizar a grande capacidade,
alimentação de baixa pressão e baixa capacidade, filtro de alta pressão. A bomba é amplamente utilizada na lavadora de carvão,
proteção ambiental, fábrica de alumínio, planta de fundição, etc.
Desenho de Construção
O gráfico de estrutura da bomba de alimentação
1. Voluta bifásica 2. Impulsor bifásico
3. Voluta de uma fase 4. Placa traseira
5. Sala de alimentação 6. Arbusto de localização
7.Expeller 8.Placa de cobertura do Expeller
9. Corpo de descompressão 10. Impulsor de uma fase
11. Barra de amarração 12. Manga do eixo
13. Placa de cobertura 14. Anel de desmontagem
15. Placa de retenção de água 16. Rolamento
17. Eixo 18. Manga espaçadora de mancal
19. Tampa de rolamento 20. Quadro
21. Tubo de curvatura
TABELA DE SELEÇÃO DE BOMBA NP-ZJW
PARÂMETROS DE DESEMPENHO DA BOMBA DE ALIMENTAÇÃO NP-ZJW
Visão geral do produto:
Possíveis Falhas e Assentamentos.
Faults
|
Reason
|
Settlement
|
1.Pump fails to discharge any water,The hand of pressure gauge beat violently
|
1.Suction pipe don`t have enough water.
2.Suction pipe blocked or the valve is locked.
|
1. Inject enough water
2.unlock the inlet valve,clear the blocks
3.Exclude the air leakage
|
2.The pump can`t discharge water,the hand of vacuum meter beat heavily.
|
1.The inlet valve is unlocked or silted up.
2.The resistance of suction pipe is too big or silted up.
3.The height of suction is too high.
|
1.Unlock the valve or desilting
2.improve the design of suction pipe or desilt
3.Lower the height of the installation.
|
3.The pump can`t discharge water,pressure gauge shows heavy pressure.
|
1.The resistance of the discharge pipe is too big.
2.The impeller blocked
3.The speed is slow.
|
1.Check and adjust the outlet pipe.
2.Clear the impeller
3. Improve the speed.
|
4.The pump doesn`t rotate
|
The volute is silted up by the blocks.
|
Clear the blocks
|
5.The capacity is not enough
|
1.The blocks of the impeller or the inlet or outlet pipe.
2.The abrasion of the impeller is heavily.
3.The speed is low to normal
4.Pump is installed unreasonably or the leakage of the inlet pipe.
5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.
6.The inlet valve not open enough or blocked
7.The packing seal leaks
|
1.Clear the impeller or pipe.
2.Change the impeller
3.Adjust the speed
4.Install again or stop leaking.
5.Decrease the height of the transport or reduce the resistance.
6.Unlock the inlet valve
7.Compress the packing tightly
|
6.The motor of the pump is overloaded
|
1.The head of the pump exceeds the head of the working condition.
2.Not consider the slurry density when selecting the pump.
3.The packing press tightly
|
1.Turn down the outlet valve,cut the impeller or lower the speed.
2.Select the motor again.
3.Adjust the the screw of the packing gland
|
7.Abnormal sound in the pump, and no water out
|
1.The resistance of the inlet pipe is too big.
2.The height of the suction is too high.
3.Cavitation occurred
4.there is air in the inlet
5.The temperature of the liquid is too high
|
1.Clear the suction pipe and sluice valve.
2.Lower the height of the suction
3.Adjust the water valve and let the pump operate in the defined limits.
4.Block the leakage.
5.Lowering the liquid temperature.
|
8.pump vibrates
|
1.pump cavitate
2.The block of the impeller single vane
3.The no concentricity between the pump shaft and motor shaft
4.Fasteners or foundation loose
|
1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.
2.Clear the impeller
3.Alignment again
4.Fasten the screw,and reinforce the foundation.
|
9.Bearing is overheat
|
1.lock the cooling water
2.lubrication is not good.
3.the lubrication oil is not clear
4.the wrong direction of the thrust bearing.
5.there is something wrong with the bearing.
|
1.Open the cooling water
2.Adjust the oil quantity
3.Clear the shaft,change oil
4.According to the inlet pressure,adjust the direction of the thrust bearing.
5.Change the bearing
|
10.Packing short life
|
The material of packing is not good
|
Change the packing
|
11.pump leak oil
|
1.High oil level
2.The rubber parts invalid
3.Assembly problem
|
1.Lower the oil level
2.Change rubber spares
3.Adjust the assembly
|
12 Pump head leaking
|
1.The rubber parts not press well
|
Assembly again or press tightly
|
PERGUNTAS FREQUENTES:
T1. Você é um fabricante de fábrica?
Sim, somos a fábrica de manufatura direta e temos mais de 10 anos de experiência nesta área.
Q2.Do você tem produtos de estoque para vender?
Alguns temos em estoque, mas os outros não. Uma vez que sempre produzimos esses produtos de acordo com as necessidades dos clientes.
Q3.Quais vantagens você tem?
A: Nós somos fabricante direto e o preço é competitivo.
B: Nosso engenheiro tem muita experiência nesta área, e podemos fazer o serviço OEM para você.
C: nós somos fábrica, e podemos providenciar cronograma de produção, de modo a entrega pontual.
Detalhes do contato:
Shijiazhuang Naipu Pump Co., Ltd.
Adicionar: No.368 Xinshi North Road, Shijiazhuang Hi-Tech Industry Development Zone, Hebei, China, 050091.
Tel: 0086-311-897162903
Fax: 0086-311-87162902
Pessoa de contato: Karen Tan
Skype: karen_naipump